BenGWeeks on Nostr: OK, if you're building, you will want some extra parts ordered up. M4 x 16mm pan head ...
OK, if you're building, you will want some extra parts ordered up.
M4 x 16mm pan head security torx tamper resistant bolts (14mm+ is fine)
These hold the front facia to the back box.
https://www.amazon.co.uk/gp/product/B0BTTRPBQV/
Tamper-proof torx wrench (T20)
To tighten the front facia Torx bolts.
https://www.amazon.co.uk/gp/product/B0D53LNNRW
M4 x 30mm carriage/coach bolts
These are to replace the bolts supplied with the coin acceptor to accommodate the thickness of the facia.
https://www.ebay.co.uk/itm/386550912089?var=653926055961
5.5mm x 2.1mm DC Power Jack Socket Female Panel Mount Connector
This allows the 12V adaptor to plug into the ATM's outside. The box assumes a diameter of 7.7mm (like these).
https://www.amazon.co.uk/dp/B01N3679B8
Rubber feet (D30x22xH15)
If you want to have this one on the table, some rubber feet will go at the bottom of the backbox with an M5 bolt. You can also use adhesive versions. Grooves in the bottom of the box will support up to 30mm in diameter.
https://www.amazon.co.uk/dp/B0CQ23M5Z5
Cabinet draw tubular 16mm lock
This will be mounted on the door. I may do a variation with an electric solenoid that can use a pin from the screen to unlock so keys will not be lost. I will create shims for different-sized locks to work with the door. NB Door design is still pending.
https://www.amazon.co.uk/Litensh-Tubular-Cylinder-Cupboard-Letterbox/dp/B09SHWXWXC/
M15 x 16mm hex socket bolts with M5 nylon nuts
To screw the rubber feet into the back box.
https://www.amazon.co.uk/16mm-Socket-Button-Head-Screws/dp/B09BG8XNM7
https://www.amazon.co.uk/Bolt-Base-Stainless-Insert-Nylock
Will also be looking into actual 16-pin connectors and alike for a soldered finish rather than push pins that are more likely to fall out.
M4 x 16mm pan head security torx tamper resistant bolts (14mm+ is fine)
These hold the front facia to the back box.
https://www.amazon.co.uk/gp/product/B0BTTRPBQV/
Tamper-proof torx wrench (T20)
To tighten the front facia Torx bolts.
https://www.amazon.co.uk/gp/product/B0D53LNNRW
M4 x 30mm carriage/coach bolts
These are to replace the bolts supplied with the coin acceptor to accommodate the thickness of the facia.
https://www.ebay.co.uk/itm/386550912089?var=653926055961
5.5mm x 2.1mm DC Power Jack Socket Female Panel Mount Connector
This allows the 12V adaptor to plug into the ATM's outside. The box assumes a diameter of 7.7mm (like these).
https://www.amazon.co.uk/dp/B01N3679B8
Rubber feet (D30x22xH15)
If you want to have this one on the table, some rubber feet will go at the bottom of the backbox with an M5 bolt. You can also use adhesive versions. Grooves in the bottom of the box will support up to 30mm in diameter.
https://www.amazon.co.uk/dp/B0CQ23M5Z5
Cabinet draw tubular 16mm lock
This will be mounted on the door. I may do a variation with an electric solenoid that can use a pin from the screen to unlock so keys will not be lost. I will create shims for different-sized locks to work with the door. NB Door design is still pending.
https://www.amazon.co.uk/Litensh-Tubular-Cylinder-Cupboard-Letterbox/dp/B09SHWXWXC/
M15 x 16mm hex socket bolts with M5 nylon nuts
To screw the rubber feet into the back box.
https://www.amazon.co.uk/16mm-Socket-Button-Head-Screws/dp/B09BG8XNM7
https://www.amazon.co.uk/Bolt-Base-Stainless-Insert-Nylock
Will also be looking into actual 16-pin connectors and alike for a soldered finish rather than push pins that are more likely to fall out.